* unnamed :results
@ 2011-01-01 23:34 Thomas S. Dye
2011-01-05 16:20 ` Eric Schulte
0 siblings, 1 reply; 3+ messages in thread
From: Thomas S. Dye @ 2011-01-01 23:34 UTC (permalink / raw)
To: Org Mode
Aloha all,
In the course of updating an Org-mode file to take account of the new
file output handling for R, I noticed a change in the naming of
results blocks. In the example below, the top #+results: line was
produced with the most recent Org-mode from git. The previous
behavior is on the following line.
#+srcname: r-complete-length-histogram-pdf
#+begin_src R :results output graphics :file r/adze_len_eg.png :var
x=whole-adzes
library(ggplot2)
adze.len <- ggplot(x, aes(length_poll))
adze.len + geom_histogram()
#+end_src
#+results:
[[file:r/adze_len_eg.png]]
#+results: r-complete-length-histogram-pdf
[[file:r/adze_len_eg.png]]
The only change (other than updating Org-mode) was the addition of
graphics to the :results header argument.
All the best,
Tom
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: unnamed :results
2011-01-01 23:34 unnamed :results Thomas S. Dye
@ 2011-01-05 16:20 ` Eric Schulte
2011-01-05 18:23 ` Thomas S. Dye
0 siblings, 1 reply; 3+ messages in thread
From: Eric Schulte @ 2011-01-05 16:20 UTC (permalink / raw)
To: Thomas S. Dye; +Cc: Org Mode
Hmm,
I think the code has always named results blocks after the code block
when the code block has a name. I would expect your "new" behavior
below to have been the standard behavior since the early days of babel.
Best -- Eric
"Thomas S. Dye" <tsd@tsdye.com> writes:
> Aloha all,
>
> In the course of updating an Org-mode file to take account of the new
> file output handling for R, I noticed a change in the naming of
> results blocks. In the example below, the top #+results: line was
> produced with the most recent Org-mode from git. The previous
> behavior is on the following line.
>
> #+srcname: r-complete-length-histogram-pdf
> #+begin_src R :results output graphics :file r/adze_len_eg.png :var
> x=whole-adzes
> library(ggplot2)
> adze.len <- ggplot(x, aes(length_poll))
> adze.len + geom_histogram()
> #+end_src
>
>
> #+results:
> [[file:r/adze_len_eg.png]]
>
> #+results: r-complete-length-histogram-pdf
> [[file:r/adze_len_eg.png]]
>
> The only change (other than updating Org-mode) was the addition of
> graphics to the :results header argument.
>
> All the best,
> Tom
>
> _______________________________________________
> Emacs-orgmode mailing list
> Please use `Reply All' to send replies to the list.
> Emacs-orgmode@gnu.org
> http://lists.gnu.org/mailman/listinfo/emacs-orgmode
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: unnamed :results
2011-01-05 16:20 ` Eric Schulte
@ 2011-01-05 18:23 ` Thomas S. Dye
0 siblings, 0 replies; 3+ messages in thread
From: Thomas S. Dye @ 2011-01-05 18:23 UTC (permalink / raw)
To: Eric Schulte; +Cc: Org Mode
Hi Eric,
I went back and looked at this again. The same code block writes a
named results block now, as it should. I must have put Org-mode in an
unstable state earlier. Sorry for the noise.
Tom
On Jan 5, 2011, at 6:20 AM, Eric Schulte wrote:
> Hmm,
>
> I think the code has always named results blocks after the code block
> when the code block has a name. I would expect your "new" behavior
> below to have been the standard behavior since the early days of
> babel.
>
> Best -- Eric
>
> "Thomas S. Dye" <tsd@tsdye.com> writes:
>
>> Aloha all,
>>
>> In the course of updating an Org-mode file to take account of the new
>> file output handling for R, I noticed a change in the naming of
>> results blocks. In the example below, the top #+results: line was
>> produced with the most recent Org-mode from git. The previous
>> behavior is on the following line.
>>
>> #+srcname: r-complete-length-histogram-pdf
>> #+begin_src R :results output graphics :file r/adze_len_eg.png :var
>> x=whole-adzes
>> library(ggplot2)
>> adze.len <- ggplot(x, aes(length_poll))
>> adze.len + geom_histogram()
>> #+end_src
>>
>>
>> #+results:
>> [[file:r/adze_len_eg.png]]
>>
>> #+results: r-complete-length-histogram-pdf
>> [[file:r/adze_len_eg.png]]
>>
>> The only change (other than updating Org-mode) was the addition of
>> graphics to the :results header argument.
>>
>> All the best,
>> Tom
>>
>> _______________________________________________
>> Emacs-orgmode mailing list
>> Please use `Reply All' to send replies to the list.
>> Emacs-orgmode@gnu.org
>> http://lists.gnu.org/mailman/listinfo/emacs-orgmode
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2011-01-05 18:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-01-01 23:34 unnamed :results Thomas S. Dye
2011-01-05 16:20 ` Eric Schulte
2011-01-05 18:23 ` Thomas S. Dye
Code repositories for project(s) associated with this public inbox
https://git.savannah.gnu.org/cgit/emacs/org-mode.git
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).