Rasmus writes:
> Hi,
>
> Rainer M Krug writes:
>
>> I want to include in a document, exported to LaTeX, a subfigure. and
>> followed the blog entry [1]. This works, but
>>
>> 1) is cumbersome and extemely LaTex  I can live with this, but is
>> there a more orgmodeisch solution?
>> 2) I cant use the link (Figure [[fig:ventLEL]]) as they got not replaced
>> by the correct LaTeX commands. This is obvious (as I did not
>> use #+CAPTION: for the caption), but is there a way, apart from
>> using the LaTeX code for these links, to get the links into the
>> document?
>
> I don't think there's an "official" way to do this. Presumably it
> /could/ use the same mechanisms as when concatenating tables into an
> equation of matrices, but at the moment there's nothing like it.
>
> I don't know if this is much better. It would probably require some
> effort to make it work in other backends than latex and it's pretty
> verbose.
>
> #+LATEX_HEADER: \usepackage{subcaption}
>
> #+CAPTION: Main caption
> #+begin_figure
> #+ATTR_LATEX: :options [t]{.45\textwidth}
> #+CAPTION: subcaption 1
> #+BEGIN_subfigure
> #+BEGIN_CENTER
> #+ATTR_LATEX: :width 3cm
> [[file:tmpEOCX1p.jpg]]
> #+END_CENTER
> #+end_subfigure
> #+ATTR_LATEX: :options [t]{.45\textwidth} :width 2cm
> #+CAPTION: subcaption 2
> #+begin_subfigure
> #+BEGIN_CENTER
> #+ATTR_LATEX: :width 3cm :center t
> [[file:tmpEOCX1p.jpg]]
> #+END_CENTER
> #+end_subfigure
> #+end_figure
>
> Hope it helps,
Thanks  it definitely does  even with labels and links.
Thanks a lot,
Rainer
Here my solution including the links to subfigures:
,
 A comparative plot of the matlab script and the R script shows that
 these two algorithms give the same results when using the same
 parameter (Figure [[fig:ventLEL]], matlab [[fig:ventLEL_matlab]], R [[fig:ventLEL_matlab_R]]).

 A comparative plot of the matlab script and the R script shows that
 these two algorithms give the same results when using the same
 parameter (Figure [[fig:ventLEL]], matlab [[fig:ventLEL_matlab]], R [[fig:ventLEL_matlab_R]]).

 #+CAPTION: Plot of the wind profile from the matlab script using the LogExpLog profile
 #+LABEL: fig:ventLEL
 #+begin_figure
 #+ATTR_LATEX: :options [t]{.45\textwidth}
 #+CAPTION: Matlab script vent5
 #+LABEL: fig:ventLEL_matlab
 #+BEGIN_subfigure
 #+BEGIN_CENTER
 [[file:inst/matlab/plots/vent5.pdf]]
 #+END_CENTER
 #+end_subfigure
 #+ATTR_LATEX: :options [t]{.45\textwidth}
 #+CAPTION: R function uLEL()
 #+LABEL: fig:=ventLEL_R
 #+begin_subfigure
 #+BEGIN_CENTER
 #+begin_src R :exports results :file rVentLEL.pdf :results graphics
 plot(runif(100))
 #+end_src
 #+RESULTS:
 [[file:rVentLEL.pdf]]
 #+END_CENTER
 #+end_subfigure
 #+end_figure
`
> Rasmus

Rainer M. Krug
email: Rainerkrugsde
PGP: 0x0F52F982